M3 x 0.75 x 10 mm machine screw

1,575 Views | 7 Replies | Last: 5 yr ago by HollyB83
HollyB83
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
6:25p, 9/4/20
A video suggests a m3x0.75x10mm machine screws but I can't seem to find the .75 pitch for m3 screws anywhere so far.

The guy doing the video is very meticulous always but I wonder if this is a typo because the only picture I can find is .50 (Course) or 0.35 (Fine).
Reply Quote
TMoney2007
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
8:34p, 9/4/20
Please post the video.
Reply Quote
HollyB83
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
In reply to TMoney2007 • 1:40p, 9/5/20


at 4:50 mark

It begins at the 4:50 time mark
Reply Quote
5 edits
BrazosDog02
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
1:13a, 9/7/20
Didn't watch video but McMaster-Carr will likely have what you want. If they don't, then they don't make it or you don't need it. Lol
Reply Quote
TMoney2007
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
In reply to HollyB83 • 8:29a, 9/7/20
The description on the video says they're M3x0.5 screws, which is a standard thread.
Reply Quote
HollyB83
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
In reply to TMoney2007 • 4:24p, 9/7/20
TMoney2007 said:
The description on the video says they're M3x0.5 screws, which is a standard thread.


Look at the 5:21 and 10:10 mark.

Where do you see in the video that they are M3 x 0.5 screws? That is certainly standard but the point of the video is to recommend 10 mm long vs 8 mm long screws and lock tite but where do you see M3 x .5 screws mentioned?
Reply Quote
HollyB83
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
4:38p, 9/7/20
4 comments down by Aleksandar Kepic the author of the video asked if the different screws used by Aleksander Kepic were M3 x 0.5 so I think the video has a typo when he has .75 pitch noted twice.
Reply Quote
TMoney2007
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
In reply to HollyB83 • 5:30p, 9/7/20
HollyB83 said:
TMoney2007 said:
The description on the video says they're M3x0.5 screws, which is a standard thread.
Loop
Look at the 5:21 and 10:10 mark.

Where do you see in the video that they are M3 x 0.5 screws? That is certainly standard but the point of the video is to recommend 10 mm long vs 8 mm long screws and lock tite but where do you see M3 x .5 screws mentioned?
The description of the video under the title.
Reply Quote
HollyB83
User Profile Ignore User Stop Ignoring
How long do you want to ignore this user?
24 hours One week Permanently Cancel
In reply to TMoney2007 • 8:27p, 9/7/20
Good find!
I never looked at the description. He had a typo in the video itself.
Thanks!!!
Reply Quote
Refresh
Page 1 of 1
 
×
subscribe Verify your student status
See Subscription Benefits
Trial only available to users who have never subscribed or participated in a previous trial.